Terscheckii Cactus Skin Cuts (Trichocereus Terscheckii) Peruvian Torch Skin Cuts (Trichocereus Peruvianus) – Very strong

Drog Wilddagga

Peruvian Torch Skin Cuts (Trichocereus Peruvianus) – Very Strong POWERFUL caapi)VERY Shaman!! Ayahuasca Normally Vine(Banisteriopsis used Shaman!! BLACK POWERFUL caapi)VERY

ydrolysed ergot alkaloids, to unreacted lysergic acid, or lysergic acid hydrazides to iso- LSD and God knows what substances created by the mishandling of the raw materials and product, a contaminated product is much easier to make than a pure one. The use of large volumes of solvents poses twin problems: obtaining them and disposing of them. Both problems are made vastly Practical LSD Manufacture 70 simpler by recycling the solvents. Just because a solvent has been used once in a given stage of the process does not mean its useful lifetime is over. For example, the solvent used for defatting the crop is easily made as good as new by distilling it to free it of its load of fat. Other solvents are not so easily recovered for re-use because the procedure calls for the given solvent to be removed from the product by vacuum evaporation. In this case, the solvent can be collected in a cold trap placed along the vacuum line on its way to the vacuum source. If a pump is used to create the vacuum, such a trap is vital to prevent solvent vapors from getting into the pump oil, thereby ruining the lubrication and the vacuum created. A cold trap can be constructed of either glass or steel; it need only be large enough to hold the solvent collected, and airtight so as not to ruin the vacuum with leaks. This cold trap is then cooled down with dry ice during vacuum evaporations to condense the solvent vapors in the trap. The solvent recovered in the trap can be re-used in the given stage of the process from whence it came. I would not co-mingle recovered solvents from different stages. For example, chloroform from the alkaloid extraction of the crops should be kept for that usage, and not be used for LSD crystallization, because it will also contain some ammonia and methanol. The recovery of ether, for example, from method 2 of lysergic acid production, poses a special problem. This problem is the formation of explosive peroxides in ether during storage. Ether containing water and alcohol, as would be the case for this recovered solvent, does not form much peroxide. There is a possibility that dry ether can be made free of peroxides by shaking the ether with some 5% ferrous sulfate (FeSO4) solution in water prior to distilling. Failure to do this may expose the operator to a fiery explosion during distillation. Ice water flowing through the condenser, and an ice-chilled receiving flask, are required to get an efficient condensation of the ether during distillation. 11 Keeping Out Of Trouble 71 II Keeping Out Of Trouble The dangers of LSD manufacturing do not end with the possibility that the cooker may spill some of the stuff on himself and fry his brain. There is a much more malignant danger facing those who embark upon this course: Johnny Law. The conduit through which those shit-eating dogs travel to get to you is your associates. If you are cooking alone with no partners in crime, your safety has been impro Drog Wilddagga Viable Colubrina Anadenanthera Colubrina crops is put into a 500 ml flask along with a solution made up of 150 ml ethyl alcohol, 150 ml water, and 100 grams KOH. Next, 15 ml of hydrazine hydrate is added. This hydrazine should be the monohydrate, which is 64% hydrazine. If a weaker variety has been scrounged up, this can be made to work by adding more, and using less water. Now the flask should be fitted with a condenser, and flushed with nitrogen. Then heat the flask in an oil bath to gentle boiling for 4 hours. A slow stream of nitrogen to the flask during the reflux averts the danger from hydrazine. The flask is next cooled, and the contents poured into a sep funnel of at least 1000 ml capacity. The batch is then extracted with 600 ml ether, followed by 600 ml of an 85-15% mix of ether and alcohol. Finally, one more extraction with 600 ml of 85-15% ether-alcohol is done. All of the desired product should now be extracted into the solvent, and out of the water. This fact should be checked using a black light to look for the characteristic blue fluorescence. The combined solvent extracts should now be lowered to a pH of about 2 using HC1. At this point, a precipitate should form, and it should be filtered out. The precipitate should be washed free of entrained product with 4-1 ether-alcohol, and the washing added to the rest of the filtered solvent. Now 2750 ml of water should be added to the solvent, and the mixture placed in a gallon and a half glass jug or 5000 ml beaker. To this should be added 3 portions of cation exchange resin in H* cycle. Cation exchange resin is a common item of commerce used in deionized water systems. Check the yellow pages under "water" and see which of the local Culligan men offer deionized water systems. The deionizers come in two-tank systems with one tank packed with cation exchange resin to remove calcium, magnesium and sodium from the water. The other tank has an anion exchange resin to remove chlorides, sulfates, and so on. It is no great task to buy cation exchange resin from these outlets. The resin consists of tiny plastic beads coated with the exchanger. In the case of the cation exchangers, Practical LSD Manufacture 44 this is generally a sulfonate. "In H* cycle" means that the resin is charged up and ready to go. This is generally done by soaking the resin in 20% sulfuric acid in water for a while, then rinsing with distilled water. Check the directions on the container of resin. Steer clear of mixed resins that contain both anion and cation exchangers. If the Culligan man is too stupid to know the difference, or doesn't know what he has, keep looking until you find one who knows his business. The treatment with three portions of cation exchange resin in H* cycle should be done as follows: Each portion of resin should weigh about 15 grams. The first portion is added, and then the mixture should be stirred strongly or shaken for about 10 minutes. The product will come out of the liquid, and stick Anadenanthera Colubrina Viable Seeds Drog Wilddagga

 Methcathinone Ayahuasca

These products should not be used by people with heart disease, diabetes, hypertension, or kidney disease ayahuasca cusco Drog Wilddagga Pihkal Cocaine Peruvian Torch Skin Cuts (Trichocereus Peruvianus) – Very strong (Some websites, no joke, charge you extra for the funnel Fresh Kratom Extract (Mitragyna speciosa) Drog Wilddagga Ayahuasca BLACK (Negra) Vine(Banisteriopsis caapi)VERY POWERFUL Normally ONLY used by Shaman!!

@Tuesday, February 20, 2018 8:02:04 PM